Skip to main content

How to Review Object Mask Tracking With a Client

· 5 min read
Creative workflow guides from FlowLabs

The client likes the brighter jacket on a paused frame. During playback, a hand crosses the sleeve and a patch of the wall brightens too. The adjustment has the right strength, but its mask needs another pass.

Review a tracked mask twice. First, play the finished effect through the shot and its neighbouring cuts. Then inspect the frames where the subject changes shape, passes behind something, or leaves the picture. Keep the decision about the look and the list of tracking repairs in the same review note.

Adobe's November 2026 Premiere 27.0 release lists improvements to Object Mask tracking, mask file size and recovery. Those changes make this a useful moment to revisit how you review a selective effect. The walkthrough below focuses on a mask used to adjust one moving object in a shot. You can use the same review method with a mask built in another application. Premiere 27.0 release notes

State what the mask should change​

Before showing the shot, describe the intended adjustment in one sentence. In a hypothetical clothing film, the brief might be to lift the jacket slightly while keeping the face and the wall at their existing levels. That gives the client a clear question and gives the editor specific boundaries to inspect.

Prepare the shot with its final framing, speed and neighbouring cuts. If you are still choosing between two strengths of the effect, label the alternatives and keep the rest of the image consistent. You can settle the preferred strength during the session and record any tracking repairs needed to carry that choice through the shot. How to compare two colour grades

Check your application version when following setup instructions. Adobe's current Object Mask guide describes selecting a subject in the Program Monitor and refining the selection by adding or subtracting areas. It also distinguishes Sharp and Smooth edge modes. If you change the mode or tracking settings while preparing the review, save a version so you can identify what the client saw. Adobe Object Mask guide

Watch the effect before displaying the mask​

Play the shot at normal speed with the adjustment visible and mask outlines hidden. Let the playback run from the preceding shot into the next one. Ask the client whether the intended object holds their attention and whether the adjustment feels consistent as it moves.

Watch for a bright or dark edge, a patch of background changing with the subject, or the effect briefly disappearing. If someone spots a problem, pause and mark the range. Replay it from a little earlier so everyone can see how it begins. A frame that looks acceptable on its own can become distracting when the boundary changes over several frames.

Show the mask itself when you need to explain a repair. Bring the client back to the finished image to confirm the result. For a colour decision, judge the final look on the agreed reference viewing setup and record any local finishing checks still required.

Inspect the parts of the shot that challenge tracking​

Work through the entire used shot locally, then return to the marked ranges for closer inspection. These are useful places to begin.

Moment in the shotWhat to inspect
A hand or prop crosses the subjectFollow the boundary through the overlap and check the first clear frames afterwards.
The subject turns or changes shapeLook for areas of the object that lose the effect and nearby areas that acquire it.
Hair, fabric or motion blur changes the outlineWatch for a fringe that flickers or becomes conspicuously hard against the background.
The subject reaches the edge of the pictureCheck whether the effect stays attached as the subject enters or exits.
The shot begins or endsCheck every used frame, including frames exposed by the latest trim.

Slow playback and frame stepping help locate a repair. After changing the mask, play the range at normal speed again with the effect applied. Keep enough of the surrounding action to see whether the correction holds through the transition into and out of the repaired area.

If a subtle edge is hard to judge in the remote feed, mark it for local inspection and share a reference export when needed. Confirm that the final export contains the correction. A clean frame in the editing application's monitor alone leaves that delivery check open.

Keep a repair note the editor can reproduce​

Suppose the jacket adjustment looks right until the hand crosses it. At that point, the brightened region reaches onto the wall for six frames. Use a note like this, with your own version and timecode.

Reference — Clothing film v08, jacket close-up, 01:00:18:04–01:00:18:09 at 25 fps.

Observed problem — The wall brightens beside the sleeve as the hand crosses the jacket.

Decision — Keep the current jacket brightness. Repair the boundary through the overlap and check its recovery afterwards.

Verification — Replay the repaired shot between its neighbours and inspect the matching frames in the review export.

If the cut changes, locate the passage again before carrying the note into the next version. How to carry client notes across cut versions

Use a live session when the client needs to see the repair in context and decide whether the shot is ready. You can send playback to Flow through a WHIP encoder and use the room microphone to discuss the marked passage after playback. Flow encoder setup · Review a shot with your client in Flow